REGIONAL WAREHOUSE NETWORK FOR RAPID DELIVERY | 877-288-8077

Peerco Adhesive Remover - 321

$117.75/Gallon
Quantity
Add to Wishlist
Part# 02-00234
MFR Model# PEERCO 321

Overview

Peerco #321 Adhesive Remover is designed to remove the adhesive residue when replacing de-icing boots. However, #321 will remove 3M 1300L and many other adhesives. This product is environmentally and user friendly as it does not contain ketones like MEK. Peerco #321 Adhesive Remover has a pleasant scent and is made of all natural ingredients. Apply #321 liberally to surface and allow to stand for 10 minutes. You may rinse off with water and wipe dry.

1 gallon.
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Features

  • Contains no ketones
  • Environmentally friendly
  • Semi jelled – clings to vertical surfaces
  • Works in 10 minutes or less
  • May be rinsed off with water
  • Tested by Scientific Material International, Inc.
  • Conforms to Douglas CSD #1 Stripper
  • Conforms to Boeing D6-17487 revision J
  • Removes 3M #1300 L and many other adhesives
  • Shelf life 2 years in sealed cans

Reviews

Silver S Verified Purchase

PEERCO ADHESIVE REMOVER 321

January 29, 2024

James C Verified Purchase

PEERCO ADHESIVE REMOVER 321

January 1, 2024

Works best on fast boot and 1300L. I’ve used it for years. I apply it with a gloved hand, spreading it on in a thick layer over the entire area needed. Then immediately cover the area with thin plastic drop cloth material and tape down the edges. Let it work for an hour or so, then start cleaning. Only uncover a small section at a time or it will dry out or you will have to reapply.

Alex
April 28, 2023

Takes off adhesive and black tar with minimal effort. 100% worth it.

John B Verified Purchase

PEERCO ADHESIVE REMOVER 321

October 7, 2022

This stuff works!!! Brush it on, wait 10 minutes and scrape of the old adhesive. I used this to clean all the old glue from the floor boards on the interior of my 1976 Piper Arrow as I worked my way through the refurbishment of the interior. It made a real crappy job much more tolerable and saved me a ton of time. Well worth the cost.

Lawrence F Verified Purchase

PEERCO ADHESIVE REMOVER 321

August 12, 2022

Turned material over to mechanic. Havent had a chance to find out how it worked but assume if it didnt, Id have heard by now.

A.c. C Verified Purchase

PEERCO ADHESIVE REMOVER 321

August 8, 2022

Works Great on the Cessna tar that has been in place for over 60 years. True labor saver....

Terry J Verified Purchase

PEERCO ADHESIVE REMOVER 321

January 21, 2022

Perco 321 is awesome. We removed the adhesive on our wings and it only took 1 hour. Just glop it on and 10 min later scrape it off with a plastic scraper. Comes off like butter. We’ve told all our friends! Huge time and energy saver.

Frank M Verified Purchase

PEERCO ADHESIVE REMOVER 321

November 23, 2021

Did a nice job of removing old adhesive (1300L) from the wings in preparation for new boots. Doesn’t have an unpleasant chemical odor like most solvents, but the orange aroma can get a little nauseating over time, especially in poorly ventilated areas. Overall good product would buy again.

Ned S
May 24, 2021

I don’t usually review stuff as I buy stuff from Spruce all the time. This stuff actually works, it’s expensive, but when you consider how much time you’ll save... it doesn’t eat paint, it just emulsifies glue/adhesive’s.

Tom
September 21, 2019

Q&A

Please note, Pilotshop.com's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop.com assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: I am wanting to remove the black tar/spray in rubber insulation in a Cessna 180. Will this remove this junk?

Yes, this is designed to remove adhesive residue. Effectiveness is case by case and dependent on the specific adhesive and age of the adhesive.

Q: Will this harm my plexiglass windows?

We do not have any data showing it's harm to plexiglass, but we always recommend using this product in a small test area first before applying to any surface to ensure it will not cause damage.

Q: Is this best applied with a brush of some kind or something like a putty knife?

It is a semi-gel so you should be able to brush it on.