Pilotshop.com
- Shop All Categories
- Browse Headsets
Contact Us
Call Us
Sign In
- Photo may represent series and not specific product
- SHARE
Aerospace Logic 2-1/4 Electronic Vertical Speed Indicator 0-6000 Fpm With Altitude Encoder
MFR Model# VSI200E
FREE Shipping
- JUMP TO
- Overview
- Specifications
- Reviews
- Q&A
Overview
|
Aerospace Logic AOG Expedite Available, additional charges will apply. The VSI200 is the most accurate Vertical Speed Indicator available for your aircraft. It exceeds all the requirements of TSO C8e and AS8016A while providing the following functionality:
|
 |
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. |
Specifications
Certification / Compliance
TSO C8e & C88b
Canadian STC (PENDING)
FAA STC (PENDING)
Certified as primary replacement or for secondary use
Environmental
DO-160E
C1CAASXXXXXXYBXXBBBCSBA1C11XXAX
Software
DO-178B Level C
DC Power Source
Input voltage 6 to 36 VDC
Power consumption 125mA
Load dump tolerance +60V
Direct spike tolerance +/- 60V
Cable spike tolerance > +/- 1KV
Operating Temperature
Constant operating -20C to +55C
Short term operating (1hr) -40C to +70C
Storage -55C to +85C
Display Units VSI
Feet per Minute
Display Units Standard Pressure Altitude
Feet
Accuracy Demonstrated
+/- 1'
Accuracy Certified (Exceeds)
SAE AS8016A, AS8003
LCD Display
Sunlight readable LCD
176 X 192 display pixels, 65,535 colors
RS-232 Data Output
1 second per full sequence at 57.6K bps (8/N/2/N)
Interface Connector Electrical
DB-25
Interface Connector Static Port
1/8" NPT
Software Functionality
Rate of climb or descent
Rate of climb or descent and Standard Pressure Altitude
Standard Gillham Grey Code output to transponder
Performance Specification Statement per AS8003 Section 4.4
a) Entire instrument power requirement is 125mA. The encoder section is capable of sinking (grounding) and maximum of 1.15A of current (115mA X 10 outputs).
b) The encoder shall interface to transponder units for which the following Gillham Grey Code Outputs are acceptable (most Mode C transponder units):
- Each encoder lead is a sink driver that will ground up to a 60V input. Minimum voltage is 3V.
- Each encoder lead will sink a constant current of 115mA. Minimum current requirement is 525uA.
- Maximum ON impedance is less than 3 Ohms.
- Maximum ON (logical “1”) voltage is 60V. Minimum is 3V.
- Leakage current for (4) above is less than 100nA
- Maximum OFF (logical “0”) voltage is 0.6V. Minimum is 0.12V.
- Maximum rate of altitude change is 100mS.
- Switching bandwidth is greater than 1,000 kHz.
- Provides standard 10-Bit Code.
Dimensions Hole
Standard 2 1/4" aircraft mounting hole
Dimensions Enclosure
2.45 X 2.45 X 0.9
Dimensions Including Pressure Port
2.45 X 2.45 X 1.725
Weight (excluding harness)
4.30 oz
Finish
Black anodized 6061 aluminum
Q&A
Please note, Pilotshop.com's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop.com assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.