|900-4CP-0 (4 Cyl) for NO tanks Primary|
|900-4CP-2 (4 Cyl) for L/R 2 tanks setup complete Primary|
|900-4CP-4 (4 Cyl) for L/R and Aux 4 tanks setup complete Primary|
|900-6CP-0 (6 Cyl) for NO tanks Primary|
|900-6CP-2 (6 Cyl) for L/R 2 tanks setup complete Primary|
|900-6CP-4 (6 Cyl) for L/R and Aux 4 tanks setup complete Primary|
|900-7CP-4 (7 Cyl) for L/R and Aux 4 tanks setup complete Primary|
|900-8CP-4 (8 Cyl) for L/R and Aux 4 tanks setup complete Primary|
|900-9CP-4 (9 Cyl) for L/R and Aux 4 tanks setup complete Primary|
there WILL be a $200 fee: Required Order Form
The EDM-900 includes an ALL IN ONE Bright VGA Display with over 40 functions including fuel level. It is FAA STC approved to replace all engine instruments in over 1000 aircraft and all probes, sensors, and transducers are included. The EDM-900 has a built in EDM-800, plus many other gauges in combination together.
WARNING: The product may contain and/or expose you to a chemical(s) or substance(s) which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. www.P65Warnings.ca.gov
After testing all my old gauges and finding them of poor quality now I had all of the 50 year old gauges , wires , probes and sensors removed and thrown away. My shop put in the JPI EDM 900 and it was the best decision I have made while updating a Cessna 172. While you are doing this always have your fuel tank sending units cleaned and recalibrated for accurate measurements. This unit is great.
Installed on my Archer II, removed all old gauges except RPM. High quality probes on the primary JPI-900. Works perfect! Worth every penny!
just learning it!
I give the edm 900 4 stars instead of 5 because in the documentation is says you might have issues with calibrating your old fuel gauges. Well after talking with the service personel it was made clear they never calibrate. Just to let you know they would not take back the $200.00 harness and I had to buy a new harness to hook up to the new cies sender units $1000.00. Plus the Time to remove and reinstall the new harness. Agrivating to say the least. Love the gauge with the fuel flow option,spot on every time with fuel consumption . The cies fuel senders are fantastic. C182n
Please note, Pilotshop's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
Per JPI, The EDM-900 does not come with a fuel pressure transducer. It is an option that can be added to the order.
A Garmin 796 can interface with the EDM900 through a data cable such as part number: 11-10044.
Per the manufacturer: It is recommended to use the new probes included with the kit.
Yes, please see part number 10-06563 for the flush mount option.
No, only non-primary data can be changed.
Yes, RS-232 connections can provide GPS data to the EDM 900.
Yes, the EDM 900 has a tach function.
Yes, GPS information can be shared for features such as fuel required to destination.
Per JPI - 3.56" deep (connectors recessed)- 4.81" wide, 3.47" high, fits a 3.125" hole.
No, this is not a plug and play replacement for the EDM 830.