REGIONAL WAREHOUSE NETWORK FOR RAPID DELIVERY | 877-288-8077

Rolo-Flair Flaring Tool 37°

$136.95/Each
Quantity
Add to Wishlist
Part# 12-01575
MFR Model# 212FB

Overview

Operates on same principle as Imperial #507-FA but flares 1/8" (primer line) and 3/4" tubing as well. Size: 4"W x 4"D x 8"H. Wt. 2-1/2 lbs. Excellent tool for bench - not for close-quarter work. Not for use on Stainless Steel Tubing.

Can be used with the following tubing sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, & 3/4.

   
California Prop 65 Warning Symbol

WARNING: The product may contain and/or expose you to a chemical(s) or substance(s) which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. www.P65Warnings.ca.gov

Reviews

I found it MUCH easier to achieve good flares with this tool than the 2-piece tools.

Brad S Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

November 15, 2022

Ftt D Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

September 28, 2022

Easy to use. Practiced a couple times on scrap tubing then finished my fuel line in a couple minutes. Very intuitive.

Cristina A Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

September 15, 2022

excellent tool. Five stars

Michael T Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

May 13, 2022

Does a great job on -2 copper lines!

Steve C Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

January 24, 2022

I was skeptical to use it inside my airplane from other reviews but it worked great

James D Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

November 19, 2021

Great flaring tool. I used this when the Ryobi wouldnt flare a 1/4 stainless line

Robert M Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

November 17, 2021

High quality tool however, it is large and heavy so better suited for bench work.

Richard G Verified Purchase

ROLO-FLAIR TOOL 37* 212FB

June 7, 2021

Works well as advertised.

Kevin
January 11, 2021

This tool works amazing for flaring gas much nicer than the old one.

Dave
December 3, 2020

Q&A

Please note, Pilotshop's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: What sizes of tubing will this tool flair?

Part number 12-01075 can be used with the following tubing sizes: 1/8, 3/16, 1/4, 5/16, 3/8, 7/16, 1/2, 5/8, & 3/4.

Q: Can this tool be used to flare mild steel lines also?

No, the specs indicate it is to be used with copper or aluminum alloy tube.

Q: Will this Rolo-Flair Flaring tool is ok for 5052 tube?

Per Vendor: "It depends on the diameter of the tube itself. If he is working with either of the following sizes Flares 1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 5/8", and 3/4" tubing then it should work for his application."

Q: Will this tool work with 3/8 copper nickel tube?

Yes, it should work fine with that tubing.

Q: Is this a 37 degree flare?

Yes, this is a 37 degree flare.