FREE SHIPPING ON ORDERS OVER $350 (USA ONLY - SOME EXCLUSIONS APPLY) | 877-288-8077

S/S RAPCO EXHAUST GASKET RA632837

$3.35/Piece
Part# 08-05237
MFR Model# RA632837
EngineRapco PNModelDescriptionPart Number
ContinentalRA632837Solid
Stainless Steel
S/S RAPCO EXHAUST GASKET RA63283708-05237

Overview

RAPCO manufactures FAA-PMA approved exhaust gasket replacements for Continental and Lycoming engines. High quality, economical stainless and copper beaded gaskets. Extra thick spiral woundstyle available “Blow Proof”

Download Rapco Exhaust Gaskets Application Chart
Download Complete Rapco Catalog PDF
   
California Prop 65 Warning Symbol

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

  • Frequently Purchased With
  • Customers Also Viewed

Reviews

2 stacked per flange

Robert L Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

October 31, 2023

These are stamped sheetmetal and youll want two for each cylinder. For best results, use them with the concave sides together with a wee bead of red RTV between them. then another wee bead of red RTV on each outer side of the sandwich, to ensure a very good seal between the head and the manifold.

Gelston A Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

September 14, 2023

Working OK.

Joe V Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

July 25, 2023

Morandini A Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

February 15, 2023

Works well.

Randall M Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

December 6, 2022

Good Quality from Rapco

Flying M Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

November 8, 2022

Good product, for the Continental GO 300 E are necessary 2 gaskets per exhaust, so 6 cilíndrese 12 gaskets.

Sergio G Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

July 13, 2022

just the right part for my O300.

Douglas V Verified Purchase

S/S RAPCO EXHAUST GASKET RA632837

September 4, 2021

It looks like the ones that came off the motor but I have not used at this time.

Peter C
March 12, 2020

excellent

Dick E
November 9, 2019

Q&A

Please note, Pilotshop.com's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop.com assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: Regarding RA630365 copper exhaust gaskets: Are these used in pairs, where you would stack 2 for each flange, or just one per flange? So on a 4 cylinder engine, would I need 8, or 4 total?

Only one of the RA632837 gaskets are required per cylinder. The RA630365 have a raised bead that can be stacked if desired, but not required

Q: Is ACS pn. 08-05229 used as one per cylinder or two per cylinder?

This is used as one per cylinder.

Q: Can part # 08-05270 (spiral wound exhaust flange gasket) be reused, or does it need to be discarded after each use?

Per Rapco: It is recommended that all exhaust gaskets, flat and spiral wound, are changed each time they are removed. They are designed to crush into place to block high temperature exhaust gases from eroding any uneven mating surfaces. If reused they may not seal properly.

Q: If using 2 gaskets per cylinder, do the raised beads oppose each other or should they interlock?

Make sure cylinder and exhaust stack flanges are flat. Check aircraft maintenance manual for proper installation. In most cases solid gaskets should be installed in pairs with raised beads interlocked and facing away from the cylinder. Also check maintenance manual for exhaust nut torque spec. Re-torque after a hot run.

Q: What are the dimensions of the RAPCO COPPER EXHAUST GASKET RA75118?

2.25" od, 1.765" id, .05 thick, 2.5" hole center to hole center.