Trig makes the world’s smallest and lightest certified GA transponders. The TT22 Trig compact transponder can fit into the tightest panel space. This allows general aviation, light sport and glider pilots to fit other instrumentation or displays that otherwise might not have been possible.
The TT22 is a class 1 transponder suitable for use in higher performance aircraft flying above 15,000 feet and / or above 175 knots.
The TT22 transponder is easy to operate and with a crisp, bright display it is also easy to read in all lighting conditions. The higher powered TT22 can be used in IFR and VFR flight in high performance aircraft, over 175 knots and/or above 15,000 feet. The transponder control head is splash proof too so it’s ideal for open cockpit and seaplane operations.
Mode A and C transponders are now being replaced by Mode S technology which is optimised for tomorrow’s airspace requirements. Despite its modest size the TT22 is a heavyweight performer, at 250 watts nominal power output this class 1 transponder meets the latest FAA TSO C166b standards for ADS-B Out.
Trig were the first company in the world to offer a ‘mandate ready’ certified 1090ES ADS-B Out compliant solution. The TT22 is popular in the U.S. where a certified WAAS GPS, and a ground air determination device are also required forming the ideal 2020 ADS-B solution. It’s worth remembering that to receive all ADS-B In transmissions in the U.S. the FAA requires a functioning certified ADS-B Out device, so don’t miss out on airspace information - fit a Trig TT22.
All Trig products come with a two year warranty, supported by our global network of Approved Trig Dealers and Approved Trig Service Centers in the U.S. and Australia.
The Peregrine Switch Kit is required for installation per STC Part Number: 10-05913.
Great little unit! Installed like a breeze with my Aircraft Spruce harness. Small but Class 1 powerful unit. Recommend to everyone looking forward to 2020 mandate!
Please note, Pilotshop's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
The TT 22 11-08322 comes with transponder head, remote transponder, mounting tray and connector kit for both units. Shielded wire, coax cable, coax connector and transponder antenna must be purchased separate. (The Trig has a female TNC connector out).
Yes, the same antenna for a mode C transponder can be used on a mode S transponder.
Per the distributor, there currently is not a TSO in regard to interfacing the TT22 with the GTN 650.
For part number 11-08322 Trig has introduced TC20 software v1.10 that allows manual adjustable backlighting. The backlight is not automatic and is manually adjustable through the TC20 controller. The LCD has a reflective screen at the back which allows it to be read in direct sunlight. At night readability is dependent on the adjustment of the backlighting, the brighter the adjustment the easier it will be to read.
If there is no other WAAS GPS source available then the TN70 will be required to provide positional data to the TT22 for ADS-B compliance.
No. It is recommended that you use the Trig TN 70.
No, you would still need an approved WAAS GPS source, such as the TN 70 to be ADS-B out compliant.
The TN-70 (pn: 11-13061) is an approved WAAS GPS source for the TT-22.
The Trigg TT-22 is ADS-B compliant when hooked up to a WAAS GPS source. The manual does not mention ADS A compliance.
The TT22 transponder is certified to TSO-C166b and meets the requirements of AC 20-165B when directly connected to the GPS units listed below, and will form the basis of a 14 CFR 91.227 compliant ADS-B installation.
The following combinations are available under Trig STC program for certified aircraft.