Q&A
Please note, Pilotshop.com's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Pilotshop.com assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
Q: What is the appropriate antenna cable for the transponder with a 6 ft run?
You have the option of RG 400 or RG 58 coax cable. RG 400 is a higher quality cable but either will work.
Q: Is the Skyview system from Dynon usable for certified aircraft?
No, the Skyview system is not TSO'd and is intended for experimental aircraft.
Q: Are the D-sub pins on the Dynon cables standard or high density pins?
They are standard density pins.
Q: Can you provide a diagram of the EMS fuel flow sensor ? Dimensions ?
This would be part number 10-01196. The diagram is under the documents tab.
Q: Does the oil pressure sensor (10-04823) come with wire leads? I see on the Kavlico site that the sensors can come with either a connector only or can include a connector with 18 leads.
As supplied by Dynon Avionics, this (and all other "Kavlico" sensors) do come with a connector and wires.
Q: Can the Dynon EMS-D10 be mounted and used in a portrait position? In other words, turned 90 degrees.
No, the EMS D10 can only be installed horizontally.
Q: Can this Dynon Skyview system be installed on a King Air C90?
No, this system is not FAA Approved and is intended for use in experimental aircraft only.
Q: Although the Dynon SkyView system is not TSOd..can it be fitted as a back up system in a certificated aircraft--or are products such as Garmin the only option....
Unfortunately, this unit cannot be installed in a certificated aircraft even as a back up. Please see the certified G5 for a qualifying unit.
Q: Do you sell the Skyview 10 HDX?
Yes, you can find it on our website by keyword searching "Skyview HDX" or part # 10-06254.
Q: Is the part # 10-01168 thermocouple wire sold by the foot?
Yes, part # 10-01168 is sold by the foot.
Q: Does the Autopilot Panel, part #'s 10-05614 and 10-05613 come with the necessary parts to make the 15-pin connector?
Yes, these will include the connector kits.
Q: What type of servo is provided with the Sonex Roll with servo kit 10-05886? Is it a SV32L (long arm)?
The servo provided is the SV42EL.
Q: Do I still need to buy the SV-MAP-270 unlock key if I buy the system now? According to Dynon this certificate is included in all the Skyview display packages that is purchased.
As of August 2016, NAVIGATION MAPPING software now included with the following DISPLAYS: SkyView Classic (D1000, D700), SkyView Touch, & SkyView HDX
No, if you purchase the SkyView Touch System now, you will not not need to purchase the SV-MAP-270 unlock key.All functionality of that software will be included with your purchase.
Q: Does SV-D1000 now come with synthetic vision included?
Yes, the SV-D1000 includes synthetic vision. Here are the contents:
SV-D1000/A 10" DISPLAY
SV-HARNESS D-37
SYNTHETIC VISION
Q: I currently have a D100 and D120 in my plane. Can I buy a Skyview screen and connect my currently installed D100/D120 harnesses to the Skyview screen?
No, this new Skyview system would require a new Dynon harness.
Q: Are there worldwide maps on EFIS for navigation?
The only world wide maps available for the HDX system are low resolution terrain maps. Base and high resolution maps are done by the region.
Q: What is the difference between the Sky View Touch and the Sky View HDX? Is the touch basically the same only with the touch screen capability?
The Skyview HDX has a higher definition screen than the Skyview touch, it also has an angled knob control as opposed to the Touch having a flat control panel.
Q: Is this Dynon EMS-D10 instrument certified or only experimental aircraft?
Experimental aircraft only.
Q: Is the part number 10-01171 a Kavlico product? Trying to determine if it will fit.
This probe is directly from Dynon.
Q: Is the EGT probe part # 10-01169 one probe or 4 (L4C) for the price?
Part # 10-01169 is priced and sold individually.
Q: What is included with EGT/CHT 4 Cylinder 6ft. (10-01179)? Is it just the wire? Probes? Hose clamps for EGT?
This is a pinned out connector harness with thermocouple wires inserted in the connector. No probes are included.
Q: Does P/N 10-01847 EGT 2 come with the probe? If not, what is the part no for the egt probe and harness?
No, p/n:10-01847 is just the harness. For the probe you can view p/n: 10-01844.
Q: Concerning ADAHRS-DUAL #10-04018, does it include the mounting kit #11-14152 and the Network Splitter #10-03948?
No it does not. Those will be a separate purchases.
Q: How are the supplied harnesses terminated on each ends for the SV-XPNDR-261 kit #11-11953 and the Skyview ADSB #11-11938, pins crimped or not, connectors assembled or not?
The xndr side of this harness will be complete. The other side will be bare wire.
Q: Which product is a Dynon single EGT probe with hose clamp? I cant tell from descriptions. One looks like clamp only. The other looks like wire only.
This is the sender with a clamp.
Q: hi can we purchase the any EFIS (skyview HDX) system from you directly? we can have A&P install the system.
We can only sell the Dynon Skyview for install in experimental aircraft. For certified aircraft, it must be purchased from the installer.
Q: Can I install the Dynon Skyview EFIS in LSA?
Please contact your A&P for legal conditions of install. We can only sell this system for experimental aircraft install.
Q: What is the tip diameter for EGT #10-01844?
It is 0.1 inch.
Q: Hi, How long are the wires on Dynon 10-01169 and 10-01170? If extension wire is required (sold by the foot) 10-01167 and/or 10-01168, does it come bare wire and we have to supply connectors? If so do you have part numbers for required connectors to fit 01169 and 01170?
Probe wire length is 24 inches, the EGT/CHT harness from the skyview is 6 feet.
Contact Us
Call Us
Sign In
FREE Shipping
Verified Purchase